Fulcrum Pin
This fulcrum pin fits the lower front control front eye bolt and the rear suspension spring shackles. The original pins had 3/8" BSF threads. These replacement items have 3/8" UNF threads. Pins are supplied with proper nuts.
FITS:
FITS:
- Morris Minor 1948-1971
Leaf Spring Mounting Pad Rear
Rear Spring mounting pad for semi elliptic spring vehicles (Fits Either Side Of Road Spring) Quantity 4 required per car.
Fits:
Fits:
- Morris Minor 1948-1971
U-Bolt Semi-Elliptic Rear Spring
Large U-bolts are used to mount the rear springs to the chassis. While these may not wear out, they are subject to all kinds of abuse under the car. 5 leaf rear springs, Quantity of 4 required per car
Fits:
Fits:
- Morris Minor Sedan, Tourer 1948-1971
U-Bolt Semi-Elliptic Rear Spring
Large U-bolts are used to mount the rear springs to the chassis. While these may not wear out, they are subject to all kinds of abuse under the car. 7 & 8 leaf rear springs, Quantity of 4 required per vehicle
Fits:
Fits:
- Morris Minor Traveller, Pickup, Van
Spring Locating Plate
Locating Plate for Spring Pad and U-Bolts. Plate is fitted on both upper and lower side of spring. Quantity 4 is required per Sedan, Tourer and Traveller.
Rear Shackle Metal Plate
Rear Shackle Metal Plate (2 Required Per Side). Quantity 4 is required per Sedan, Tourer and Traveller or LCV
Fits:
Fits:
- Morris All
Rear Spring Front Locating Pin
Rear Spring front locating pin (2 Required Per car). This pin fits Sedan, Tourer and Traveller but not the trucks
Fits:
Fits:
- Morris Sedan, Convertible, Traveller
Locating Plate Front Shackle Pin Rear Leaf Spring
Locating plate for front spring pin (2 Required Per car). This pin fits Sedan, Tourer and Traveller but not the trucks
Fits:
Fits:
- Morris Sedan, Convertible, Traveller
REAR SPRING INSTALLATION & BUSHING KIT
This kit has all of the hardware to properly install the rear spring on a Morris with the semi elliptic spring.
The kit contains: (4) U-Bolts, (4) Spring Pads, (8) Shackle Bushings, (8) U-Bolt Nyloc Nuts (grade 8), (8) U-Bolt Washers (grade 8), (4) Shackle Locking Washers (grade 8), (4) Shackle Nuts (grade 8)
Fits:
The kit contains: (4) U-Bolts, (4) Spring Pads, (8) Shackle Bushings, (8) U-Bolt Nyloc Nuts (grade 8), (8) U-Bolt Washers (grade 8), (4) Shackle Locking Washers (grade 8), (4) Shackle Nuts (grade 8)
Fits:
- Morris Sedan, Convertible 1955-1971
Buffer Rear Axle
To prevent tire rub or suspension damage when you hit a large bump or lean the car during hard cornering, both the rear suspension is equipped with rubber buffers (bump stops). The large bump stops are clamp to the rear axle housing via the U-bolts. The rubber does decay with age and exposure. For safety it should be in good condition. Quantity 2 required per vehicle
FITS:
FITS:
- Morris Minor Sedan, Tourer, Traveller 1948-1971
REAR SPRING INSTALLATION & BUSHING KIT
This kit has all of the hardware to properly install the rear spring on a Morris with the semi elliptic spring.
The kit contains: (4) U-Bolts, (4) Spring Pads, (8) Shackle Bushings, (8) U-Bolt Nyloc Nuts (grade 8), (8) U-Bolt Washers (grade 8), (4) Shackle Locking Washers (grade 8), (4) Shackle Nuts (grade 8)
Fits:
The kit contains: (4) U-Bolts, (4) Spring Pads, (8) Shackle Bushings, (8) U-Bolt Nyloc Nuts (grade 8), (8) U-Bolt Washers (grade 8), (4) Shackle Locking Washers (grade 8), (4) Shackle Nuts (grade 8)
Fits:
- Morris Traveller 1955-1971
REAR SUSPENSION LOWERING KIT
Lower your car with our aluminum lowering block kit. The blocks fit between the spring and axle, effectively lowering the car by approximately 1 1/4" to 1 1/2". (the reduction in height will vary depending on the quality of your existing suspension) Recommended for use with standard semi-elliptical springs only. Not for use with re-arched race springs
FITS:
- Morris Minor Sedan, Convertible, Traveller 1955-1971
Telescopic Damper(Shock) Conversion Kit-Rear
Telescopic rear damper (shock) conversion. This kit improves the handling of the Morris and softens the ride. These are oil shocks not harsh gas filled performance shocks. This kit is designed to give a very good ride quality while controlling the rear axle over rutted roads. The best upgrade you can do for smoother ride on a Morris. Complete bolt on kit, no fabricating required. Kit is complete with all hardware and instructions.
Fits:
Fits:
- Morris Sedan, Convertible, Traveller
Radius Arm (Anti-tramp) Kit
Radius Arm kit for Morris Minor. This anti tramp bar kit is designed to reduce the rear spring wind up for performance driving. The kit is totally bolt on and no extra holes need to be drilled or welding required.
FITS:
- Morris Minor Sedans, Convertibles, and Travellers 1954-1071
